DIY Bathtub Installation.
DIY Bathtub Installation.
Blog Article
We have discovered this great article about Installing A Bathtub directly below on the net and figured it made good sense to share it with you on my blog.
Mounting a bathtub isn't specifically rocket science, however it does require strong plumbing, woodworking, as well as occasionally, tiling skills. Changing an old bathtub with a brand-new one is additionally a moderately hard project. If the old bathtub is conveniently available, the job can relocate rapidly; if you need to open a wall surface to remove the old bathtub and position the brand-new bathtub, the task is a lot harder. In either case, the job is within a residence handyman's skills, although you will require a helper to move out the old bathtub and also set in the new one. Ensure you have actually qualified yourself for the task and also fit attempting it. Instead of employing a service provider to take over a halfway-completed job, it is far better to consider employing one prior to you start. Opportunities are you might need an expert plumber to make tube links.
This write-up will assist you set up a brand-new bath tub in your bathroom if you have already purchased a brand-new bathtub and also don't need to change the plan of your previous supply of water pipes.
Your tools and material checklist should comprise the following:
Planning for the Installment
Firstly, the supporting framework provided with the bathroom needs to be fitted (if required) according to the producer's directions. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is essential to ensure that if the tap includes a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bath, it is also sensible to fit a supporting plate under the taps system to avoid pressure on the bath tub.
Fit the adaptable faucet connectors to the bottom of the two taps using 2 nuts and olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make certain you make use of every one of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach all-time low of the overflow tube in a similar manner.The bath need to currently be ready to be fitted in its last placement.
Removing Old Taps
If you need to change old faucets with new ones as a part of your installation, after that the first thing you must do is disconnect the water supply. After doing so, activate the faucets to drain any kind of water continuing to be in the system. The process of removing the existing faucets can be rather problematic as a result of the limited access that is often the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the faucets. Have a cloth all set for the remaining water that will originate from the pipes. When the supply pipelines have been eliminated, make use of the same device to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the single faucets from transforming during this process. As soon as the taps have been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any kind of old sealing compound.
Prior to going on to fit the brand-new taps, compare the pipeline links on the old taps to the new faucets. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new taps to fit.
Setting up the Tub
Making use of the two wooden boards under its feet, put the tub in the called for position. The wooden boards are valuable in equally spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 tiny points.
The next goal is to make sure that the bath tub is leveled all round. This can be attained by checking the spirit level and changing the feet on the tub till the level reviews level.
To install taps, fit the bottom of the furthest versatile faucet adapter to the ideal supply pipeline by making a compression sign up with; then do the same for the other tap.
Switch on the supply of water as well as inspect all joints as well as brand-new pipework for leakages as well as tighten them if needed. Load the bath tub as well as additionally examine the overflow electrical outlet and also the regular electrical outlet for leakages.
Ultimately, deal with the bathroom paneling as defined in the supplier's user's manual. Tiling and also securing around the bath tub must wait up until the tub has actually been utilized a minimum of once as this will resolve it right into its final position.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will certainly require a plastic port to prevent damages to the string. One end of the port fits on the plastic tail of the tap and the various other end supplies a connection to the existent supply pipelines.
If you need to fit a monobloc, then you will certainly call for decreasing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next off, place the tap in the placing opening in the bath/basin guaranteeing that the washers remain in location between the faucet as well as the sink. Secure the faucet in place with the manufacturer given backnut. When the tap is firmly in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with typical faucet ports. The former kind ought to be connected to the faucet ends initially, tightening just by hand. The supply pipes can later be linked to the other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Bath tub
In the location where the bath fulfills the ceramic tile, it is necessary to secure the accompanies a silicone rubber caulking. This is essential as the installation can move enough to fracture a stiff seal, causing the water to pass through the wall in between the bathroom and the tiling, bring about issues with dampness and also possible leakages to the ceiling below.
You can pick from a range of coloured sealants to assimilate your fixtures and also fittings. They are marketed in tubes as well as cartridges, and also are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a larger space to fill, you can load it with twists of drenched newspaper or soft rope. Keep in mind to always fill up the bathtub with water prior to sealing, to enable the activity experienced when the tub remains in use. The sealer can break rather early if you do not think about this movement prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally easily offered on the market. It is recommended to fit the tiles making use of water-resistant or water resistant glue and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a person who reads about How to Install a Bathtub, I thought sharing that excerpt was sensible. Don't hesitate to take the opportunity to promote this blog if you appreciated it. Thanks for your time. Kindly check our website back soon.
This Site Report this page